SECTION 06414 CABINET HARDWARE PART 1 GENERAL 1.1 SECTION INCLUDES A. Cabinet hinges. 1.2 RELATED SECTIONS ** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required. A. Section 06400 - Architectural Woodwork. B. Section 06410 - Custom cabinets. C. Section 12300 - Manufactured Casework. D. Section 12320 - Manufactured Wood Casework. E. Section 12350 - Specialty School Fixture Casework. F. Section 12350 - Specialty Store Fixture Casework. G. Section 12510 - Office Casework. 1.3 SUBMITTALS A. Submit under provisions of Section 01300. B. Product Data: Manufacturer's data sheets on each product to be used, including: 1. Preparation instructions and recommendations. 2. Storage and handling requirements and recommendations. 3. Installation methods. C. Shop Drawings: Submit schedule showing hardware, hardware location and finishes. ** NOTE TO SPECIFIER ** Verification samples are not normally required, except on very large projects and in situations where specific model numbers have not been specified. D. Verification Samples: Two of each different item of hardware for approval by Architect. One of each pair of approved items will be returned and may be used on the project. 1.4 QUALITY ASSURANCE ** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project. A. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship. 1. Finish areas designated by Architect. 2. Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect. 3. Refinish mock-up area as required to produce acceptable work. 1.5 DELIVERY, STORAGE, AND HANDLING A. Store products in manufacturer's unopened packaging until ready for installation. B. Store and dispose of solvent-based materials, and materials used with solvent-based materials, in accordance with requirements of local authorities having jurisdiction. 1.6 PROJECT CONDITIONS A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits. PART 2 PRODUCTS 2.1 MANUFACTURERS A. Acceptable Manufacturer: Hafele America Co., which is located at: 3901 Cheyenne Dr. P.O. Box 4000 ; Archdale, NC 27263; Toll Free Tel: 888-437-7477; Tel: 336-434-8136; Fax: 336-434-8159; Email: request info; Web: www.hafele.com/us ** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions. B. Substitutions: Not permitted. C. Requests for substitutions will be considered in accordance with provisions of Section 01600. HINGES – AXIMAT 300 ** NOTE TO SPECIFIER ** Aximat hinges available in full range of hinge types, mounting, action and with trim cap unless noted otherwise. Use the following paragraph to establish the default for hinges or delete and define at each hinge. Hinge: Aximat 300 hinges meet the Grade 1 Hinge Test requirements of ANSI/BHMA A-156.9. Hinge Type: Full overlay. Half overlay. Twin mounting. Inset. Mounting: Screw mount. Press-fit. Action: Self closing. Materials: Wood. Thin Panel – Phenolic/Trespa. Glass. ** NOTE TO SPECIFIER ** Delete hinge type not required. Aximat 300 Corner Hinge with Exposed Axle, 4 mm Arm: 15 mm overlay. Matt Nickel Plate finish. Door thickness: Wood – up to 13/16 inch (21 mm). 270 degree. Self-closing. Wood Mounting: Screw. Wood Mounting: Press-fit. Aximat 300 Corner Hinge with Exposed Axle, 6 mm Arm: 6.5 mm overlay. Matt Nickel Plate finish. Door thickness: Wood – up to 13/16 inch (21 mm). 240 degree. Self-closing. Wood Mounting: Screw. Wood Mounting: Press-fit. Aximat 300 Twin Hinge with Exposed Axle, 6 mm Arm: 6.5 mm overlay. Matt Nickel Plate finish. Door thickness: Wood – up to 13/16 inch (21 mm). 180 degree. Self-closing. Wood Mounting: Screw. Wood Mounting: Press-fit. Aximat 300 Corner Hinge with Exposed Axle, 4 mm Arm: 15 mm overlay. Black Nickel Plate finish. Door thickness: Wood – up to 13/16 inch (21 mm). 270 degree. Self-closing. Wood Mounting: Screw. Wood Mounting: Press-fit. Aximat 300 Thin Panel Hinge with Exposed Axle, 4 mm Arm: 13 mm overlay. Matt Nickel Plate finish. Door thickness: Thin panel / phenolic / Trespa – up to 1/2 inch (13 mm). 270 degree. Self-closing. Mounting: Screw. Aximat 300 Corner Hinge for Glass with Exposed Axle, 3 mm Arm: 3 mm overlay. Matt Nickel Plate finish. Door thickness: Glass – 5-8mm (7/32” – 5/16”) 230 degree. Self-closing. Glass Mounting: Screw. Aximat 300 Inset Hinge for Glass with Exposed Axle, 3 mm Arm: 1/8” Gap. Matt Nickel Plate finish. Door thickness: Glass – 5-8mm (7/32” – 5/16”) 230 degree. Self-closing. Glass Mounting: Screw. . PART 3 EXECUTION 3.1 EXAMINATION A. Do not begin installation until cabinets have been properly prepared and finishes have dried. B. If cabinet preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding. 3.2 PREPARATION A. Clean surfaces thoroughly prior to installation. B. Prepare substrates carefully, using templates provided by manufacturer. C. Prepare hardware for installation using the methods recommended by the manufacturer. 3.3 INSTALLATION A. Install cabinet hardware in strict accordance with manufacturer's instructions, using tools and hardware provided by or approved by manufacturer. 3.4 ADJUSTMENT A. After cabinets have been installed in final location, make final adjustments in cabinet hardware to assure proper alignment and smooth operation. B. Repair or replace cabinet hardware items damaged during installation. 3.5 PROTECTION A. Protect installed products until completion of project. B. Properly mask or otherwise protect installed slides before finishing furniture and cabinetry C. Touch-up, repair or replace damaged products before Substantial Completion. END OF SECTION ?? ?? ?? ?? 06414-4