Thin Panel Institutional Hinge, Aximat® 300, Grade 1, Zinc Alloy

Zinc alloy, 3D adjustable, for laminated (HPL) doors

  • CAD data available.
    Please select an Item.
    • Technical documents available.
      Please select an Item.

    Filter

    Complete your selection

    Help

    Help

    Requested amount is in stock.
    Limited stock available.
    Item no longer available

    Note:
    Call us at 800.423.3531 if you have questions about availability.

    Thin Panel Institutional Hinge, Aximat® 300, Grade 1, Zinc Alloy

    Zinc alloy, 3D adjustable, for laminated (HPL) doors

    • see key

      Door Overlay Adjustment Turn screw A to adjust the overlay in both directions.
      Height Adjustment Loosen screws B .Activate the height adjustment by pushing with screwdriver into window C moving tab away, adjust ±2 mm by turning screwdriver. Re-tighten screws.
      Depth Adjustment Loosen special screws D and E , adjust manually in the prolonged hole. Security screw E can be installed at any time, 3D adjustment is still available.

    • Drilling pattern for door

    • Drilling pattern for side panel

    • see key

      Number of hinges per door
      The values in the diagram are sample measurements for doors up to 600 mm wide.
      With doors widths less than 400 mm, the minimum gap must be determined by trial mounting.
      The door’s width must not exceed its height.
      The distance between door edge and uppermost / lowermost hinge should be no more than 100 mm.
      In case of heavy loads and high leverage force, an additional hinge (dim. X max. 100 mm) mounted below the top hinge is recommended.

    Thin Panel Institutional Hinge, Aximat® 300, Grade 1, Zinc Alloy

    Zinc alloy, 3D adjustable, for laminated (HPL) doors, 3/8" overlay

    Item no. 344.75.760

    Thin Panel Institutional Hinge, Aximat® 300, Grade 1, Zinc Alloy

    Zinc alloy, 3D adjustable, for laminated (HPL) doors, 1/2" overlay

    Item no. 344.75.770

    Thin Panel Institutional Hinge, Aximat® 300, Grade 1, Zinc Alloy

    Zinc alloy, 3D adjustable, for laminated (HPL) doors, 3/4" overlay

    Item no. 344.75.790
    Product details

    Specifically designed for thin panels such Phenolic material
    Sleep sophisticated design, only 5 mm (3/16”) of knuckle is visible
    3D adjustment
    Depth adjustment of ± 1mm is achieved with oblong holes
    Height adjustment (up and down) of a ±2mm is on the door component
    The “Safety Screw” can be pre-installed at any time as it does not effect the adjustments, however, it is required.
    Integrated catch keeps doors closed, no additional magnetic catches required
    During overlay (side to side) adjustment, the knuckle moves with the door preventing a gap between door’s edge and knuckle
    Door overlay (side to side) adjustment is on the arm component as opposed to the cup component: offering continuous adjustment of +1/-2 mm in both directions
    Tested in accordance with ANSI/BHMA Grade 1 standards

    • maximum project quality in accordance with ANSI grade 1 (100,000 cycles)

    Color/finish

    Nickel plated

    Mounting

    mounting in drilled hole, screw fixing

    For door material

    laminate

    Concealed hinge version

    Full overlay/half overlay mounting

    Opening angle

    270°

    Suitable for

    Thin doors

    Material

    Zinc alloy, Hinge arm: Zinc alloy

    Door processing for assembly

    without

    Adjustment facility

    Side adjustment: -2 – 1 mm, Height adjustment: ±2 mm, Depth adjustment: ±1 mm, Height adjustment in cup part via eccentric Depth adjustment via horizontal slots in side component

    For wooden door thickness

    10 – 13 mm

    Side panel thickness

    10 – 13 mm

    Note

    When inserting screws into Phenolic material, they may corrode because of the material’s internal properties.
    Screw holes should be slightly tapered in Phenolic material to assure a tight fit.

    Supplied with

    Hinge
    Fixing material (specially coated self-tapping screws)
    1 twist drill bit ⌀ 3.3 mm per packing unit of 50 items

    Additional information

    When inserting screws into Phenolic material, they may corrode because of the material’s internal properties.
    Screw holes should be slightly tapered in Phenolic material to assure a tight fit.

    Optional accessories
    Corporate Office: Häfele America Co., 3901 Cheyenne Drive, Archdale, N.C. 27263
    Phone: 800.423.3531, Fax: 800.325.6197, Local Phone: 336.434.2322, Email: info@haefeleamericas.com
    18-Aug-2022